"The consumer's choice of spa filter . . ."

TRADE ONLY SHOP

Sanistream_Logo_600x200x72

SANISTREAM USER GUIDE 

Congratulations on your purchase of a Darlly SaniStreamTMDirect Line Filtration system. Your SaniStreamTMDirect Line Filtration system combines the highest quality hot tub filter available with an effective and efficient sanitiser dosing system to ensure sparkling clean water and safe, hygienic bathing conditions.


USAGE INSTRUCTIONS - FILTER WITH CAP & HANDLE

1. Remove the blue cap from the Darlly Direct Line filter by rotating it anticlockwise and pulling until the cap comes away from the filter.

2. Take a Darlly SpaPodTM chemical tablet dispenser (Darlly part no: DL815, available from your local  Darlly stockist). Unscrew the cap of the SpaPodTMdispenser and put to one side.

3. Using protective gloves and eye protection, add either chlorine or bromine tablets of a suitable size up to the top of the holes in the body of the SpaPodTM. Use only chlorine ORbromine, NEVERmix different chemicals together in the SpaPodTM.

NB: Some hot tub manufacturers do not permit the use of Trichloroisocyanurate ("Trichlor") tablets in their hot tubs, so check your hot tub's manual and warranty documentation to confirm which sanitisers your manufacturer recommends and/or prohibits. Darlly Europe and its agents, distributors, and partners are not responsible for any damage caused by the misuse of chemicals.

4. Replace the cap back on to the SpaPodTMby screwing it on until finger tight.

5. Replace the filled SpaPodTMback into the blue filter cap by locating the two lugs in their corresponding slots and twisting the SpaPodTMuntil it locks.

6. If this is the first time you're using your SaniStreamTMDirect Line Filtration system, adjust the outer sleeve of the SpaPodTMdispenser so that half the large holes are exposed.

7. Replace the blue cap with the attached SpaPodTMinto the top of the filter by locating the two lugs in their corresponding slots and twisting the cap clockwise until it locks.

8. Replace the filter back into your hot tub and turn the power on.

9. Check your bromine or chlorine levels daily using a quality test kit. Maintain bromine levels between 4 to 6 mg/l (ppm), or chlorine levels between 3 to 5 mg/l (ppm). If sanitiser levels are too low, rotate the outer sleeve of the SaniStreamTMdispenser to expose more holes. This will result in more sanitiser being released into your hot tub water. Re-test the water daily and repeat the process until correct sanitiser levels can be maintained. If sanitiser levels are too high, rotate the outer sleeve of the SaniStreamTMdispenser to expose fewer holes. This will result in less sanitiser being released into your hot tub water. Re-test the water daily and repeat the process until correct sanitiser levels can be maintained. 

 

USAGE INSTRUCTIONS - FILTER WITH OPEN ENDS

1. Take a Darlly SpaPodTM chemical tablet dispenser (Darlly part no: DL815, available from your local  Darlly stockist). Unscrew the cap of the SpaPodTMdispenser and put to one side.

2. Using protective gloves and eye protection, add either chlorine OR bromine tablets of a suitable size up to the top of the holes in the body of the SpaPodTM. Use only chlorine ORbromine, NEVERmix different chemicals together in the SpaPodTM.

NB: Some hot tub manufacturers do not permit the use of Trichloroisocyanurate ("Trichlor") tablets in their hot tubs, so check your hot tub's manual and warranty documentation to confirm which sanitisers your manufacturer recommends and/or prohibits. Darlly Europe and its agents, distributors, and partners are not responsible for any damage caused by the misuse of chemicals.

3. If this is the first time you're using your SaniStreamTMDirect Line Filtration system, adjust the outer sleeve of the SpaPodTMdispenser so that half the large holes are exposed.

4. Place the filled SpaPodTMback into the filter by lowering it down into the top of the filter until it rests on the SpaPodTMretaining plate a few inches down.

5. Replace the filter back into your hot tub and turn the power on.

6. Check your bromine or chlorine levels daily using a quality test kit. Maintain bromine levels between 4 to 6 mg/l (ppm), or chlorine levels between 3 to 5 mg/l (ppm). If sanitiser levels are too low, rotate the outer sleeve of the SpaPodTMdispenser to expose more holes. This will result in more sanitiser being released into your hot tub water. Re-test the water daily and repeat the process until correct sanitiser levels can be maintained. If sanitiser levels are too high, rotate the outer sleeve of the SpaPodTMdispenser to expose fewer holes. This will result in less sanitiser being released into your hot tub water. Re-test the water daily and repeat the process until correct sanitiser levels can be maintained. 

 

WEEKLY FILTER CLEANING INSTRUCTIONS

1. On a weekly basis, turn off the power to your hot tub and remove your Darlly SaniStreamTMDirect Line Filtration system from your hot tub.

2. Take the SpaPodTMchemical dispenser out of the filter and place into a dry plastic bucket or bowl.

3. Take the filter and, using a garden hose set to its highest pressure, squirt water between the pleats, systematically working through all the pleats from top to bottom to flush out all dirt and debris. Alternatively, for a really deep and more efficient clean, use the Darlly Cyclone filter cleaning attachment (part no. SC785).

4. Replace the SpaPodTMchemical dispenser back into the filter.

5. Replace the complete Darlly SaniStreamTMDirect Line Filtration system back into your hot tub and turn the power back on.

 

REFILLING THE SPAPODTM

Whilst the filter is out of your hot tub for its weekly clean, it's a good opportunity to check the condition of the sanitiser tablets inside the SpaPodTM. The tablets will gradually erode as they dissolve and add sanitiser to your hot tub's water. As space is created in the SpaPodTMby the dissolving tablets, fresh tablets should be added to ensure that adequate levels of sanistiser are maintained in your hot tub water. Never let the sanitiser tablets dissolve away completely so that the SpaPodTMbecomes empty.

 

Always remember to use protective gloves and eye protection when inspecting and refilling the SpaPodTMand always add the same tablets to the SpaPodTMas those already in there. Use only chlorine ORbromine, NEVERmix different chemicals together in the SpaPodTM. Take care when handling the SpaPodTMas a solution of concentrated sanitiser can drip out. Therefore, it's always best to do this over a dry plastic bucket so that drips do not end up on skin, clothing, or any surface which would otherwise be damaged by it. Always inspect and refill the SpaPodTMin a well-ventilated area.

 

KEEP ALL HOT TUB CHEMICALS IN THEIR ORIGINAL CONTAINERS AND SAFELY AWAY FROM CHILDREN AND ANIMALS. ALWAYS FOLLOW THE CHEMICAL MANUFACTURER'S INSTRUCTIONS ON THE PACKAGING.

 

MONTHLY FILTER CLEANING INSTRUCTIONS

1. Once a month, or more often as necessary, especially if flow to the jets is impaired or your hot tub displays an insufficient flow error, turn the power to your hot tub off and remove the Darlly SaniStreamTMDirect Line Filtration system from your hot tub.

2. Remove the SpaPodTMchemical dispenser from the filter and place in a dry plastic bucket or bowl.

3. Take the filter and, using a garden hose set to its highest pressure, squirt water between the pleats, systematically working through all the pleats from top to bottom to flush out all dirt and debris. Alternatively, for a really deep and more efficient clean, use the Darlly Cyclone filter cleaning attachment (part no. SC785). Do this to remove as much loose dirt and debris as possible.

4. Then, completely immerse the filter for 24 hours in a quality filter cleaning solution, such as SC796 Darlly Filter Cleaner, following the filter cleaner manufacturer's instructions. DO NOT UNDER ANY CIRCUMSTANCES IMMERSE THE FILTER IN THE FILTER CLEANING SOLUTION WITH THE SPAPODTMDISPENSER STILL INSTALLED WITHIN IT AS AN EXPLOSION AND THE RELEASE OF TOXIC GASES MAY RESULT.

5. After 24 hours, remove the filter from the filter cleaning solution and rinse in cold water to wash away as much of the filter cleaning solution as possible, taking care not to splash any solution onto your person or clothing.

6. Leave the filter somewhere warm to dry out completely, at least 24 hours, but ideally a week. It's a good idea to have a second filter that you can replace back into the hot tub while the other is being cleaned and dried on a monthly rotation basis. NEVER run your hot tub without a filter installed.

7. When the filter is completely dried out, replace the SpaPodTMdispenser back into the filter.

8. Replace the complete Darlly SaniStreamTMDirect Line Filtration system back into your hot tub and turn the power back on.

 

For optimal filter performance, use Darlly Duck (part no. SC805) scum sponges which soak up excess oils and surface grease which would otherwise prematurely plug the pores in the Reemay filtration media in your filter.